Product Details:
Fluke® 805 FC Vibration Meter (Now compatible with Fluke® Connect® Mobile App)
The reliable, repeatable, accurate way to check bearings and overall vibration
The Fluke® 805 FC is not a vibration pen; it’s a meter. A Fluke® meter that eliminates the confusion of vibration screening and provides reliable measurements you can trust to make critical go or no-go maintenance decisions.
Make go or no-go maintenance decisions with confidence. The Fluke® 805 FC Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition.
What makes the Fluke® 805 FC the most reliable vibration screening device available?
• Innovative sensor design minimizes measurement variations caused by device angle or contact pressure
• Consistent data quality at both low and high frequency ranges
• Four-level severity scale assesses urgency of problems for overall vibration and bearing condition
• Exportable data via USB
• Trending in Microsoft® Excel using pre-built templates
• Overall vibration measurement (10 Hz to 1,000 Hz) for acceleration, velocity and displacement units of measurement for a wide variety of machines
• Crest Factor+ technology provides reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz
• Compare vibration levels with ISO-10816 severity scales and store results to the Fluke® Connect Cloud
• Get authorization to take next steps in an instant if machine health is at risk via Fluke® Connect® Share-Live™ video call*
• Colored lighting system (green, red) and on-screen comments indicate how much pressure needs to be applied to take measurements
• Temperature measurement with Spot IR Sensor increases diagnostic capabilities
• On-board memory holds and saves up to 3,500 measurements
• External accelerometer support for hard to reach locations
• Flashlight for viewing measurement locations in dark areas
• Large screen with high resolution for easy navigation and viewing
Technical Specifications:
Specifications
Low frequency range (overall measurement)
10 Hz to 1,000 Hz
High frequency range (CF+ measurement)
4,000 Hz to 20,000 Hz
Severity levels
Good, Satisfactory, Unsatisfactory, Unacceptable
Vibration limit
50 g peak (100 g peak-peak)
A/D converter
16-bit
Signal to noise ratio
80 dB
Sampling rate
Low frequency: 20,000 Hz
High frequency: 80,000 Hz
Real time clock backup
Coin battery
Sensor
Sensitivity
100 mV g ± 10%
Measurement range
0.01 g to 50 g
Low frequency range (overall measurement)
10 Hz to 1,000 Hz
High frequency range
4,000 Hz to 20,000 Hz
Resolution
0.01 g
Accuracy
At 100 Hz ± 5% of measured value
Amplitude Units
Acceleration
g, m/sec²
Velocity
in/sec, mm/sec
Displacement
mils, mm
Infrared Thermometer (Temperature Measurement)
Range
-20 °C to 200 °C (-4 °F to 392 °F)
Accuracy
±2 °C (4 °F)
Focal length
Fixed, at ~3.8 cm (1.5")
External Sensor
Note: Fluke® supports but does not provide external sensors
Frequency range
10 Hz to 1,000 Hz
Bias voltage (to supply power)
20 V dc to 22 V dc
Bias current (to supply power)
Maximum 5 mA
Firmware
External interfaces
USB 2.0 (full speed) communication
Data capacity
Database on internal flash memory
Upgrade
Through USB
Memory
Up to 3,500 measurements
Radiated Emission
Electrostatic discharge: burst
Standard EN 61000-4-2
Electromagnetic interference
Standard EN 61000-4-3
RE
Standard CISPR 11, Class A
Environmental
Operating temperature
-20 °C to 50 °C (-4 °F to 122 °F)
Storage temperature
-30 °C to 80 °C (-22 °F to 176 °F)
Operating humidity
10% to 95% RH (non-condensing)
Operating/storage altitude
Sea level to 3,048 meters (10,000 feet)
IP rating
IP54
Vibration limit
500g peak
Drop test
1 meter
General Specifications
Battery type
AA (2) Lithium Iron Disulfide
Battery life
250 measurements
Size (L x W x H)
24.1 cm x 7.1 cm x 5.8 cm
(9.5 in x 2.8 in x 2.3 in)
Weight
0.40 kg (0.89 lb)
Connectors
USB mini-B 7-pin, external sensor jack (SMB connector)
.jpg)
PDF:
805FC
